AddictiveRC - Everything Radio Controlled
  Return to AddictiveRC Home Page Custom Built Multirotor UAV's ARF - Almost Ready to Fly Multirotor UAV's RTF - Ready to Fly Multirotor UAV's   AddictiveRC - 520-429-6493 Contact Us Online

Cellpro PowerLab Y Harness

CP8S-Y-US - Cellpro PowerLab Y Harness

New! Cellpro PowerLab Y Harness
Made with heavy duty 10AWG for connecting PowerLab and GT series chargers to the Power Station 24V55A power supply.
Two sets of EC5 connectors on one end that connect to the input cables on channels one and two of the Cellpro Dual PowerLab or GT500DUO or you may use this Y Harness to connect a single PL6 , PL8 or GT500 or two PL6, PL8 or GT500 chargers to a single power supply.
The end which connects to the power supply is left bare.
To connect to the Revolectrix Power Station 24V55A power supply, simply strip approximately one inch of wire from the bare end and connect to the Power Station binding posts.
Total overall length is 20 inches.


CP8S-Y-US

$16.95
+ Plus Shipping

Qty.
Availability: Yes


DEANS-Bare Wire Adapter

Deans-BW-US - DEANS-Bare Wire Adapter

New! DEANS-Bare Wire Adapter
This adapter is designed for battery packs with a connector on the power leads that is other than Deans.
The DNS to bare wire adapter plugs into the male Deans connector on the Multi Port Adapter (PN: MPA-XH-US).
The bare wire end is designed so that the user may install the connector of his choice.


Deans-BW-US

$2.95
+ Plus Shipping

Qty.
Availability: Yes


EC5 Connectors One Pair

EC5-M/F-1PR-US - EC5 Connectors One Pair

New! EC5 Connectors One Pair
One pair EC5 heavy duty high performance power system connectors. Blue hard plastic, ribbed grip, polarized housings. Protected from shorting and polarity reversal. Designed around 5mm bullets.
EC5 type connectors are sexed by the pins.


EC5-M/F-1PR-US

$4.95
+ Plus Shipping

Qty.
Availability: Yes


FUIM3 USB Interface Module for 2-way data communication.

FUIM3-US - FUIM3 USB Interface Module for 2-way data communication.

New! FUIM3 USB Interface Module for 2-way data communication.

This high speed, opto-isolated, PC USB interface module is designed to provide safe, 2-way communication between Revolectrix products and a PC USB port.
For use with free PC software, supports firmware updates, and PC compatible GUI software for Revolectrix Chargers and Battery Management Systems, Co-Pilot II Flight Stabilization systems and other products. Drivers for this device are available from within the available PC software programs for Revolectrix products by clicking the link "download usb driver". For more details, see the software installation page for the particular Revolectrix product in question.

Software Link page here http://www.revolectrix.com/new_applications/software/Multi4_software.html



FUIM3-US

$18.95
+ Plus Shipping

Qty.
Availability: Yes


Charbery 60 Amp 10-25Volt 1,500 watt DC Power Supply with Digital Display



HP-CHS1500 - Charbery 60 Amp 10-25Volt 1,500 watt DC Power Supply with Digital Display

New! Chargery 60 AMP 10-25V 1,500 Watt DC Power Supply with Digital Display.
Model: S1500.

HP-CHS1500

$300.99
+ Plus Shipping

Qty.
Availability: Yes


Cellpro PowerLab 6 with EC5 input cable 1000watt Multichemestry Charger

LC06S40A-EC5-MC-US - Cellpro PowerLab 6 with EC5 input cable 1000watt Multichemestry Charger

New! Cellpro PowerLab 6 with EC5 input cable 1000watt Multichemestry Charger

Charger Only!

1000W Battery Workstation including an EC5 input cable, will charge, discharge, monitor, or multiple cycle any current or future battery chemistry.
POWER you have been waiting for, safety you have come to expect in a compact, affordable Cellpro product.
Welcome to the new class of R/C battery management. Built on the amazing PowerLab 8 technology.
The extensive list of features and capabilities are rivaled only by the goal to provide the ultimate in flexibility and utility.
Out of the box, the PL6 will run circles around the competition in terms of simple, yet powerful set up and operation.
Inside the Windows environment, it's easy to alter up to 100 settings for any of the 25 user presets, gain access to 50 additional library presets in the unit or tap into the PC library.
The available cable has the mating EC5 male pin connector-to-plier clips for connecting to a car battery or power supply.
Charge up to 40amps at 1,000 watts.

LC06S40A-EC5-MC-US

$174.95
+ Plus Shipping

Qty.
Availability: Yes


Cellpro PowerLab 8 v2 EC5 Combo 5 (Expansion Channel-Ready Combo)

LC08-C5-EC5-US - Cellpro PowerLab 8 v2 EC5 Combo 5 (Expansion Channel-Ready Combo)

New! Cellpro PowerLab 8 v2 EC5 Combo 5 (Expansion Channel-Ready Combo)

This combo designed to support Expansion Channel Mode, which turns two PowerLab 8 Battery Workstations into a very-high-power (2688W), dual, independent channel device.
After setting one PL8 as, e.g., Expansion Channel #1, the Primary sends over current preset information to all Expansion Channel units connected to the "network".
A total of 16 PowerLabs can actually be networked.
In Expansion Channel Mode, you can connect a battery to each of the PowerLabs, but you only use the buttons on the Primary to start or stop operations, check data on all units.
Expansion channel mode requires that all batteries connected to all units be the same chemistry. However, the batteries can have different cell counts, and, if the preset is set up for Auto charging, the batteries can have vastly different capacities.
Note: For Expansion Channel to work, all units connected together must be the same type of PowerLab for example, PL6 to PL6, or PL8 to PL8. Don't mix and match!

Please note! Combo Contents: 2 Cellpro PowerLab 8 v2 EC5-equipped Battery Workstation with required interconnect cables to run Expansion Channel Mode (combo does not include FUIM3 PC interface).


LC08-C5-EC5-US

$479.90
+ Plus Shipping

Qty.
Availability: Yes


Cellpro PowerLab 8 v2 EC5 1,344watt Charger Combo 7 (Combo with MPA and FUM3)

LC08-C7-EC5-MPA-XH-FUIM3-US - Cellpro PowerLab 8 v2 EC5 1,344watt Charger Combo 7 (Combo with MPA and FUM3)

New! Cellpro PowerLab 8 v2 EC5 1,344watt Charger Combo 7 (Combo with MPA and FUM3)

This Charger Combo Contains:

1 Cellpro PowerLab 8 v2 EC5-equipped Battery Workstation
1 MPA-XH (Multi-Port Safe Parallel Adaptor for JST XH equipped Battery Packs)
1 MPA-to-PL interconnect cable
1 FUIM3 PC USB interface
This Combo will allow safe parallel charging of up to six 2s-to-8s same cell count LiPo Battery Packs at one time
Please note in order to use the MPA with the powerlab series, you must set the PowerLab to XH Wiring Mode either at the powerlab directly or via charge control software.

LC08-C7-EC5-MPA-XH-FUIM3-US

$319.95
+ Plus Shipping

Qty.
Availability: Yes


Cellpro PowerLab 8 v2 with EC5 input cable, 1344W, Multichemistry Battery Workstation

LC08S40A-EC5-MC-US - Cellpro PowerLab 8 v2 with EC5 input cable, 1344W, Multichemistry Battery Workstation

New! Cellpro PowerLab 8 v2 with EC5 input cable, 1344W, Multichemistry Battery Workstation

Charger Only!
UNLEASH THE POWER! The industry's first 1344W Battery Workstation now includes an EC5 input cable, and will charge, discharge, monitor, or multiple cycle any current or future battery chemistry.
POWER you have been waiting for, safety you have come to expect in a Cellpro product. Welcome to the new class of R/C battery management. This is everything you ever loved about Cellpro chargers multiplied by 100. Technologically advanced, designed from the ground up for reliable high power, geared toward the power user but simple to operate and affordable enough for the masses.
The extensive list of features and capabilities are rivaled only by the goal to provide the ultimate in flexibility and utility. Out of the box, the PL8 v2 will run circles around the competition in terms of simple, yet powerful set up and operation. But if you are the type of person looking for the utmost in flexibility and performance, look no further. The PL8 v2, in combination with the Charge Control Software offer virtually unlimited access to charging parameters.
Inside the Windows environment, it's easy to alter up to 100 settings for any of the 25 user presets, gain access to 50 additional library presets in the unit or tap into the PC library.
Major features include Advanced Power Management to help you set up and use existing Power Supplies or Pb input batteries, faster individual cell IR readout, support for all new Safe Parallel Adapters which enable charging/discharging multiple packs simultaneously, Expansion Channel Mode for turning multiple PL8 v2's into one workstation, regenerative discharge with input power supply protection built in.
The new PowerLab 8 with EC5-equipped input cable includes a one foot long, 10AWG input wire terminating with an EC5, female pin connector. Revolectrix also has an available 2 foot long plier clip assembly to support the new version of the PowerLab 8. The available cable has the mating EC5 male pin connector-to-plier clips for connecting to a car battery or power supply.

LC08S40A-EC5-MC-US

$239.95
+ Plus Shipping

Qty.
Availability: Yes


CellPro Multi-Port Safe Parallel Adaptor for HX Compatable Battery Packs

MPA-XH-US - CellPro Multi-Port Safe Parallel Adaptor for HX Compatable Battery Packs

New! CellPro Multi-Port Safe Parallel Adaptor for HX Compatable Battery Packs

Works with CellPro PowerLab Chargers 2s-to-8s Lipo Batteries.

MPA-XH-US

$64.95
+ Plus Shipping

Qty.
Availability: Yes


Cellpro PowerLab, Plier Clip Assembly, 2 ft, 60AMP

PCA-60A-US - Cellpro PowerLab, Plier Clip Assembly, 2 ft, 60AMP

New! PowerLab 60A Plier Clip Assembly for connecting the new PowerLab EC5 battery workstation to a lead acid battery or power supply. Cable is 2 foot long, 10AWG, has an EC5-equipped male pin connector on one end, and two 60A capable plier clips on the other end.
Plugs directly into the PowerLab EC5-equipped units. Allows quick-connection to PowerLab input supplies like Lead Acid batteries and certain AC/DC power supplies. Great accessory for the PowerLab series battery workstations.


PCA-60A-US

$15.95
+ Plus Shipping

Qty.
Availability: Yes

© AddictiveRC LLC - All Rights Reserved | Website Development and Design by TYCOMM.NET